General MFP Configuration

Xerox Office (EIP, XSA, JBA)

YSoft SafeQ Xerox Terminal Embedded is implementation of YSoft Terminal Professional in Xerox devices supporting a combination of EIP, XSA and JBA technologies, allowing usage of embedded accounting and GUI.
Terminal is integral and inseparable part of the YSoft SafeQ Server solution and operates only when connected to the server. Terminals work within the TCP/IP enabled networks only.

Tested Devices

This part describes first how to configure Xerox MFP in general; then particular MFPs are discussed more in details. You need to configure each device first in order to communicate with SafeQ.

Xerox MFP	Firmware
Xerox ColorQube® 8700/8900	FW 071.160.223.04200+	see Xerox multifunction printers built on ConnectKey
Xerox ColorQube® 9201/9202/9203	FW 060.050.009.30823 (rechecked against FW 061.050.225.10300)	see Xerox multifunction printers built on Endeavor and Xerox ColorQube 92xx Configuration Differences
Xerox ColorQube® 9300 series	FW 071.180.203.23400+	see Xerox multifunction printers built on ConnectKey and Xerox ColorQube 93xx Configuration Differences
Xerox Phaser 3635	-	see Xerox Multifunction Printers with Samsung controller
Xerox WorkCentre® 5222/25/30	FW 1.207.8	see Xerox WorkCentre 52xx EIP Configuration
Xerox WorkCentre® 5325/5330/5335	FW 1.201.2	see Xerox multifunction printers with Fuji Xerox controller
Xerox WorkCentre® 5632/38/45/55/65/75/87	FW 025.054.060.00035 validated against 025.054.065.00260, Note: This is the Single board controller (SBC) FW version, For the Multi-board (MBC) replace the 025.054 with 021.120)	see Xerox multifunction printers built on Endeavor
Xerox WorkCentre® 5800 series	071.190.103.23400+	see Xerox multifunction printers built on ConnectKey
Xerox WorkCentre® 6400	-	see Xerox multifunction printers built on Endeavor
Xerox WorkCentre® 5700 series	System FW 061.130.220.35400, Controller FW 061.130.32701	see Xerox WorkCentre 57xx Configuration Differences
Xerox WorkCentre® 7120/25	FW 071.013.041	see Xerox multifunction printers with Fuji Xerox controller
Xerox WorkCentre® 7425/7428/7435	System FW 75.3.1, Controller + PS ROM 1.222.18 updated based on System FW 75.14.43	see Xerox WorkCentre 74xx EIP Configuration
Xerox WorkCentre® 7200 series (7220/7225, but not 7228/7235/7245)	FW 071.030.103.23400+	see Xerox multifunction printers built on ConnectKey
Xerox WorkCentre® 7500 series	FW 061.121.224.2730+	see Xerox multifunction printers built on Endeavor
Xerox WorkCentre® 7800 series	FW 071.010.103.23400+	see Xerox multifunction printers built on ConnectKey
Xerox D95, D110, D125, C60/70		similar to Xerox multifunction printers with Fuji Xerox controller
Xerox WorkCentre® 7600 series	FW 040.033.53375	see Xerox multifunction printers built on Endeavor and Xerox WorkCentre 76xx Configuration Differences
Xerox® VersaLink™	-	see Xerox VersaLink EIP Configuration
Xerox® AltaLink™		see Xerox AltaLink EIP configuration

General Notes

Supposed you are configuring new MFP with default settings. If you are configuring older device with lot of customized settings, it may be useful to reset it to factory defaults first.
Most settings can be configured via internal web page of MFP with administration interface. Web interface of each device can be different, depending on device model. Language of the interface is mostly controlled by preferred language setting of the browser. Note that support of various browsers can differ between particular MFPs. To enter web interface, insert <MFP IP> to the browser address bar (you will be connected to http or https page based on MFP's current setting).

Default credential (As described in Xerox Admin Guides) is login: admin, password: 1111. For some devices, default login: 11111, password: x-admin.
It is often referred to SNMP community in this guide – by this, it is always mean SNMP Write community.
Newer devices support Self Address Assignment – it is recommended to turn this feature off

images/download/attachments/21955474/self-assign.png