At a Glance

FCC statements

§ 15.21 Information to user
The user's manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.

§ 15.105 Information to the user
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Step 1. Complete the Before-You-Begin checklist

Before you begin installing the terminal, complete this checklist:

If possible, register and acquire access to the Y Soft online help desk a day or two before you begin the installation.
Obtain the Terminal Ultralight installation packages and a small Phillips screwdriver.
Make sure YSoft SafeQ Server is installed and running.
Write down the terminal's serial number (located on the back of the terminal).
Make sure the Control Interface cable is the correct cable for the MFP you are connecting the terminal to.
Refer to the MFP/cable part number compatibility list that Y Soft provided you or go to Hardware Compatibility List (HCL) and check the list there.
If the cable you have is not correct, find the correct cable before you proceed. The cable may be among other Y Soft packages at the location where you are installing the terminal.
Obtain the following information:
1. SafeQ server IP address
2. Does the network support DHCP?
3. If it does not support DHCP, obtain this additional information:
4. Terminal IP address
5. Netmask address
6. Gateway IP address
7. DNS server IP address
Information about the MFP or printer:
1. IP address
2. Serial number
3. Model number

Step 2. Check package contents

Check to make sure you have the following items (included in several packages):

Main package:

- Terminal Ultralight
- Ethernet cable
- Power supply adapter

NOTE: The package also includes clear plastic cable wrap for the Ethernet cable.

images/download/attachments/21955522/main_package.png

Accessory packages:

- Control interface cable (Blocking cable)
- MFP Universal Mounting Kit (bracket, screws, washers)

NOTE: The Control Interface cable for your MFP may be different from the one shown here.

images/download/attachments/21955544/package_2.png

Step 3. Connect cables

Connect cables in the order shown in this diagram.

NOTE: You must connect the Control Interface cable before you connect the Power Supply Adapter cable.

The printer has to be connected to network directly or by switch in the UltraLight terminal.

Step 4. Terminal's configuration

Terminal Ultralight requires TCP/IP connection to the YSoft SafeQ server. Terminal has own IP and MAC address.

For the proper network configuration you can use:

Configuration utility for hardware terminals (Termtool)

Step 5. SafeQ server configuration

1

Log in to the SafeQ Web administration with sufficient rights to manage devices.

2

Go to Devices > Printers selection and click the e dit icon next to the device or double click on the device.

images/download/attachments/21955522/device_edit.png

3

Go to Terminal tab and insert, select Hardware terminal option and enter Terminal serial number of your Terminal Ultralight. This serial number equals to serial number written in Remote configuration tool for hardware terminals (first column).

Afterwards click on Save device. e

images/download/attachments/21955522/device_ultralight.png

Step 6. Mount the terminal

Depending on the type of bracket included with the terminal, mount the bracket to the MFP, to the wall, or to a nearby object such as a desk or table.
To mount the terminal onto the MFP, follow these steps:

1	Remove 2 screws from the back of the terminal.
2	Attach the mounting bracket to the terminal.
3	If you have not already done so, write down the terminal's serial number (located on the back of the terminal).
4	Use the screws and washers included with the mounting bracket to mount the bracket and terminal onto the MFP.
5	Cover the Ethernet cable with the clear plastic wrap (included in the plastic bag with the cable). Start the wrap about 4 or 5 inches (10 – 12 cm) from the back of the terminal.

Step 7. Verify installation

1

At the terminal, enter a PIN; then press OK.

NOTE: The PIN you use must be one that you have already addedin the SafeQ system.

2

Check to make sure the MFP panel unlocks (that is, the panel lights up and comes on).

If the MFP unlocks:
Installation is now complete.
If the MFP does not unlock:
Follow the procedures for getting help as described in "Submitting a problem report to Y Soft support" on page .